10 mm foam heel support: comfort and support at moderate speeds.

Easy opening/closing

Flex (3/10) is forgiving of mistakes and improves comfort.

Flexibility

EVA foam sole: 80% air insulates from cold ground.

Thermal insulation

Easy to get on. Flexible foam: maximum comfort. Thermoformable liner.

Fitting comfort

Ultralight outsole with large studs for good grip on all types of snow.

Traction

Ultralight cushioning EVA sole (80% air).

Cushioning

Very comfortable, these boots make learning easier and help you progress.

Condition

Skill Level

heat moldable liner

tightening zone

Flex

Type of Liner

Tightening Type

Laces and a blocker that is easy to use for fast tightening. The outer tightening system uses classic laces.

Quick tightening system

Adequate flex is something we strive for. It improves comfort, reduces physical fatigue, and allows you to fully enjoy your day in the snow. It helps beginners adopt the right position on the board: ankles flexed to avoid straight legs. Snowboarding demands fast reactions, and keeping knees bent is important. You don’t want to start with a boot that’s too stiff.

Boot flex/stiffness

The Flex Up enables you to add 2 out of 10 flexion points (with Flex Up, this boot has a rigidity of approximately 5/10).
This is a plastic accessory which is inserted into the tongue of Decathlon snowboard boots produced from the 2022/23 season onwards. A pocket has been included in the design to keep it in the ideal position.
The Flex Up adds stiffness: If your boot turns more limp, give it a second life.

Adding Flex Up

Foot support is essential for steering your board. The level 1 liner has 4 features:
1. Liner that can be thermoformed at home 
2. Comfort Heel Pad ankle foam 
3. 4-point liner tightening
4. Hook-and-loop tab on the top of the liner

Heel support: level 1 liner (/3)

Thermoforming is only possible in built-in ovens measuring 56 cm x 60 cm x 56 cm (22” x 23.5” x 22”) equipped with a fan mode. Do not attempt in a gas oven or small toaster oven with visible heating elements.

1. Thermoforming the liner by yourself: Warning

1. Heat your oven to 80°C in convection mode. 
2. Remove the inner soles from the liners. Place the liners on a baking sheet covered with a piece of parchment paper.
3. Wait 15 minutes.
4. Put them on with a pair of ski or snowboard socks and tighten them (not too much).
5. Put on the boots on and tighten fully. 5. Wait for 15 minutes. 
This operation can be repeated if necessary.
For use in a built-in oven (56 cm x 60 cm x 56 cm/22” x 23.5” x 22”) only

1. How to thermoform the liner yourself

Ankle padding fills the hollow under and behind the ankle, keeping the heel firmly in place.
The level 1 liner is made of a relatively soft, one-piece material with 10 mm (0.39”) thick foam ankle pads.
The goal is to provide heel-foot support that matches the boot’s performance level. In fact, the faster you go, the more energy is deployed and the more support your foot needs.
Comfort Foam provides maximum comfort.

2. Comfort Heel Pad ankle foam

4-point tightening for good foot support. It holds the foot in place around the ankle.

3. 4-point liner tightening

The top of the liner has hook-and-loop strips, enabling you to hold the tongue of the liner in place at the sides, no matter how your foot is moving. 

4. Hook-and-loop strip on top of liner

The insole of this boot is flat. It offers comfort and thermal insulation. 
If you really need added support for your foot, here’s what you can do: 
- add a sole that is pre-formed at the arch and heel area
- add a sole that can be thermoformed to your foot This is the most effective solution.

Insole

Our Ultralight sole is 100% EVA.
EVA is a very light material with 80% air. This material resists abrasion while maintaining its damping properties. It is naturally very insulating and protects you from the cold ground.
The lug tread offers excellent grip without retaining snow.

Sole: grip, traction, cushioning, and thermal insulation

1. Put the boot on. 
2. Tighten the boot. 
3. Stand up.
4. Your big toes should touch the tip of the boot without excessive pressure.
5. Bend your legs forward; your big toes should move back, no longer touching the front of the boot.

Sports/

Winter Sports/

Snowboarding Gear/

Snowboard Boots/

dreamscape

Flexible Snowboard Boots – SNB 100